I haven't used the TDS in years but now trying again. I reinstalled the software and started up the program and MSFS 2024 it said it was connected. So I started the Pilots Dash 7 and the screens came up yellow with a message WASM module not found. 

Am I doing something wrong? I dont even know what a WASM is.

I am having a problem getting TDS GTNXi to turn on in MSFS2024.  

The TDS GTNXi shows up with a black screen in MSFS2024.  

I am using FlightSim Builder G1000nxi touch monitors.  The FlightSim Builder launcher app setup has a dropdown menu to select for use of TDS GTNXi but the unit does not show up on the G1000 touch panel as it should. This happens in MSFS2024 and Xplane 12.  

Any idea as to how I can get the TDS GTNNXi to turn on and work in MSFS2024 and Xplane 12?  
Is there a file there a file I must load in a community folder?  

Thanks

Hi,

I'm trying to get the TDS GTNxi working with the TorqueSim SR22, but I can only get black screens.

When I go into the TDS menu and select a GPS, I get a pop-up with the bezel, but nothing can be clicked and the RXP GTN in the panel goes black.

I have tried various combinations of settings, but can't get the TDS GTN working in the SR22.

Everything is up to date.

The TDS GTN works in other aircraft *without* the RXP version needing to be installed.

What do I need to do to get it working, because allegedly it does work, but no-one is saying how!

Thank you.

Hello,  I am running the H160 helicopter on MSFS and trying to use the TDS GTNXI Navigation on both pilot and co pilot instruments.  When I install the software using the manager, the expected three folders are installed into the ‘Community’ folder not the Community2024 one.  Both folders are created by MSFS.  When I go into the aircraft, both nav units work.  When I close MSFS then go back into the game the nav units are black.  I have uninstalled and reinstalled many times now.  Sometimes the system for works, following a reinstall, but only for one cycle.  Often it does not.  I have checked my Norton Anti Virus and the manager and sim exe files are whitelisted.  I can run TDS before I launch MSFS and all looks well.  When the sim launches TDS closes (as I would expect).  If I remove the instrument folder from the community folder, launch TDS, all is well.  If I launch MSFS then the TDS screen then goes black. Not really sure what to now try.  Hopefully someone can point me in the right direction.

Many Thanks

Shugsta

Hi, 

I'm not sure whether this question should be for you or the aircraft's developer. but let's see. the modules on the mentioned aircraft powers on once I turn on the battery, which isn't correct, it should power on with the Avionics bus, adn this is causing a conflict with the X-chatter app (not the main issue I know), so, the elecPower.Source is set to 4 in the ini file, and I've tried a couple of other values, assuming that they were right and the modules should only work if the Avionics switch is turned on, but I had no luck, so I've had to rollback my change. Any thoughts here pelase? 

I can't figure out what I'm doing wrong.
Using the TDS GTNXI 750/650...
While flying a GPS LPV approach, I don't see the Glideslope indicator show up in the HSI.
The autopilot flies the approach just fine and tracks the glideslope to the runway from the FAF, but the glide slope indicator is not displayed.
I've tried various TDS settings and can't seem to correct this.
This might be OK if only flying with the autopilot, but I also want to hand-fly approaches following the GS indicator. (or needle).
I'm currently mainly using the Black Square Bonanza Professional, but have also tried this using the Piper Dakota with the 750/650.
Am I missing a setting? Or perhaps using the 750/650 incorrectly during the approach?
Any support is appreciated.

Are there plans for the GTNXi to work in the FSS 727-100?

There is an option for the GTNXi in the plane's binder, but the GTNXi option is greyed out in the passenger, freighter and vip variant.

I got an interesting problem with my x-plane 11 installation of the GTNXI. Antivirus turned off, installation into x-plane 11 and x-plane 12 had no errors. Loaded up the default Cessna 172 and all is well in x-plane 12. However, X plane 11 only gives me black screens.  Nothing in the suggest errors. Also, I only have the tds Plug in active. No other Plugins.

Any help is appreciated

HI, it happens a lot to me, the screen of the main unit (sometimes the secondary) keeps flickering upon avionics power up, it keeps flickering between the main black screen with the CONTINUE button and the main icons screen, which makes it unusable. The only solucion is to reboot the whole PC, restarting the sim doesn't fix it, so, it happens now on the mentioned plugin like 2/5 flights. THought to share this with you, in both VR and non-VR.

unfortunately, it's impossible to capture a screenshot.

Thanks!

I'm running MSFS2020 and I typically fly the JPLogistics Cessna 152. With the TDS GTNXi on the panel, the setup closely resembles my actual panel (except I have a GTN375 in RL). The autopilot works fine with this plane in the sim, but if I select the JPLogistics 152 with wheel fairings, on the ground, the altitude setting reads 86458.69 ft, and I'm unable to change it anything else. Rebooting the autopilot with the pad doesn't help. If I select the C152 without the fairings, there's no problem, but my actual plane does have fairings, so I'd rather fly the model that matches. Any ideas on why this is happening and tips on solving the issue would be appreciated! TIA